CertsPoint
Sign In Get Started
See all results for ""
Exams About Us
Sign In Get Started
Exam Overview
Exam Code 350-601
Exam Name Implementing and Operating Cisco Data Center Core Technologies (DCCOR) & CCIE Data Center
Vendor Cisco
Total Questions 489
Last Updated 26-Oct, 2026
Free 350-601 Questions Get Premium Access
Why CertsPoint?
  • Latest & Verified Questions
  • Detailed Explanations
  • Regular Updates
  • Full-Length Practice Tests
  • Boost Your Exam Confidence

PDF Study Materials

Downloadable guides and resources

Practice Tests

Full-length tests with real exam experience

Progress Tracking

Monitor your performance and improvement

Study Anywhere

Access on desktop, tablet, and mobile

Excellent
4.6 (398 Up Votes)
Secure Payment Privacy Protected Money Back Guarantee

Free 350-601 Practice Questions

Explore 4 free practice questions for the Cisco 350-601 exam and review the answers and explanations to support your preparation.

  1. Question 1

    Single answer

    An engineer must configure OSPF routing on Cisco Nexus 9000 Series Switches. The IP subnet of the Eth 1/2 interface for both switches must be advertised via OSPF. However, these interfaces must not establish OSPF adjacency or send routing updates. The current OSPF adjacency over the interface Eth1/1 on SW1 and Eth1/1 on SW2 must remain unaffected. Which configuration must be applied to both Nexus switches to meet these requirements?

    • Option A:
      interface ethernet 1/2 passive-interface default
      Correct
    • Option B:
      Interface ethernet 1/2 Ip ospf network point-to-point
      Correct
    • Option C:
      interface ethernet 1/2 ip ospf passive-interface
      Correct
    • Option D:
      interface ethernet 1/2 no ip ospf passive-Interface
      Correct
    Show Answer & Explanation Hide Answer & Explanation

    Correct Answer: C

    Explanation

    The ip ospf passive-interface command is used to prevent OSPF adjacency and routing updates from being sent or received on a specific interface, while still advertising the interface subnet via OSPF. This command is useful for stub networks or loopback interfaces that do not need to form OSPF neighbor relationships. The other commands either enable OSPF adjacency by default, change the OSPF network type, or disable OSPF passive mode. Reference: Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide, Release 9.3(x) - Configuring OSPF [Cisco Nexus 9000 Series Switches], Configuring OSPF, Configuring OSPF Interfaces Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide, Release 9.3(x) - Configuring OSPF [Cisco Nexus 9000 Series Switches], Configuring OSPF, Configuring OSPF Passive Interfaces Cisco Nexus 9000 Series NX-OS Unicast Routing Configuration Guide, Release 9.3(x) - Configuring OSPF [Cisco Nexus 9000 Series Switches], Configuring OSPF, Configuring OSPF Network Types

  2. Question 2

    Single answer

    Which configuration statically assigns VSAN membership to a virtual Fibre Channel interface?  

    • Option A:
      switch(config-vsan-cb>#
      Correct
    • Option B:
      vsan 100 bind interface fc 3/1
      Correct
    • Option C:
      switch# vsan 100 fc 3/1
      Correct
    • Option D:
      switch(config-vsan-db)# vsan 100 interface vfc 31
      Correct
    Show Answer & Explanation Hide Answer & Explanation

    Correct Answer: B

    Explanation

    The vsan bind interface command is used to statically assign VSAN membership to a virtual Fibre Channel interface. This command overrides the VSAN membership that is derived from the physical interface or the default VSAN. The other commands are either invalid or do not apply to virtual Fibre Channel interfaces. Reference: Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide, Release 9.3(x) - Configuring Virtual Fibre Channel Interfaces [Cisco Nexus 9000 Series Switches], Configuring Virtual Fibre Channel Interfaces, 

  3. Question 3

    Single answer

    An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image. What is expected to occur in this case? 

    • Option A:
       The system defaults to the backup image version
      Correct
    • Option B:
      The system defaults to and boots into the GOLD firmware image
      Correct
    • Option C:
       The system defaults to the GOLD firmware image
      Correct
    • Option D:
      The system defaults to and boots into the kickstart image
      Correct
    Show Answer & Explanation Hide Answer & Explanation

    Correct Answer: A

    Explanation

    The system will automatically revert to the backup image version if the endpoint fails to boot from the new firmware image. This is a feature of the Fabric Interconnects that ensures high availability and reliability. The GOLD firmware image is used for diagnostics and troubleshooting, not for normal operation. The kickstart image is used for booting the Nexus switches, not the Fabric Interconnects.

  4. Question 4

    Multiple answers

    An engineer is implementing OTV on a transport that supports multicast. The solution needs to meet the following requirements: • Establish adjacency to the remote peer by using multicast. • Enable OTV advertisements for VLAN 100 to the other site. Which two commands should be configured to meet these requirements? (Choose two.)

    • Option A:
       otv site-vlan 100
      Correct
    • Option B:
      otv data-group 232.2.2.0/28
      Correct
    • Option C:
      otv use-adjacency-server 172.27.255.94
      Correct
    • Option D:
       otv extend-vlan 100
      Correct
    • Option E:
      otv control-group 232.1.1.1
      Correct
    Show Answer & Explanation Hide Answer & Explanation

    Correct Answer: B, D

    Explanation

    To establish adjacency to the remote peer by using multicast, the engineer needs to configure the otv data-group command with a multicast address range that is unique for each site. This command specifies the multicast group that is used to send and receive OTV data traffic.